These signals are received by the X10 PRO Modules. 2 3ģ Introduction How it works The Digital Clock Timer plugs into any AC outlet in your home and transmits digitally encoded signals over your house wiring instantly or at the times you set. However, if (within 4 seconds) you press Once you will change that program to occur only once, if you press security you will change the program to occur at different times each day (variably). Advancing to a particular time (in the Prog Set/Review mode) and then pressing a number ON or OFF key will set an on or off time for that Module, every day. This will stop the buzzer and will set the alarm off again in 10 minutes. There is a handy snooze feature which lets you cancel the alarm buzzer by pressing any key. Channel number 1 also activates an internal buzzer so you can us it as an alarm clock too! You can program up to 8 X10 PRO Modules from the Digital Clock Timer and you also have instant control of 8 Modules. What it does The Digital Clock Timer plugs into any AC outlet in your home and you set it like a digital alarm clock. ![]() Always be aware of what appliance you are turning on or off so that potentially dangerous situations will not occur. Therefore, do not use with high power heating devices such as portable heaters. If an electric heater is turned on by remote control while clothing just happens to be draped over it, a fire could result. If that should happen, your coffee pot may be damaged from overheating. For example, an empty coffee pot can be remotely turned on. That s obvious - but there can be some unexpected consequences. ![]() Before you begin Keep in mind that your X10 PRO System will always turn lamps and appliances on or off the instant you press the buttons. You can even turn off everything in the system with one button. You can turn on ALL lights connected to Lamp Modules and Wall Switch Modules with the touch of a button if you hear a suspicious noise at night. You can manually turn off your child s radio or night light from your bedside. It has a snooze feature so you can sleep a while longer and you can turn the alarm off on weekends. You can keep the Digital Clock Timer by your bedside and it will wake you up on weekdays. There is even a Security Mode that automatically varies your programmed time each day so your home doesn t look like it s controlled by a timer. You can program your Modules to go on and off at the same time every day or you can set your radio to wake you up Once only, for an early morning flight. You can have your outside lights as well as inside lights and appliances go on and off at preset times to give your home a lived-in look while you are away. 9 Setting a timed event to occur in the 'Security' mode Reviewing timer events If the display shows FULL Selector switch Instantly Controlling Modules Alarm settings Setting the alarm buzzer To cancel the wake up alarm Suspending the wake up function Changing the Letter Code Setting up the Modules Troubleshooting Intercom systems Power interruptions Battery backup Battery test Introduction The X10 PRO Digital Clock Timer controls up to 8 X10 PRO Modules automatically or instantly. ![]() 9 Setting a timed event to occur once only. 9 Setting something to happen every day at the same time. Installation complete.1 PRO Model XPMT4 Digital Clock Timer Owner's ManualĢ Contents Introduction. Send an X10 OFF Command to turn it OFF.The device may turn on immediately if the Factory left the internal relay in the ON condition.Be sure the device is turned-on, if it has an On/Off switch. Plug the Device, to operate, into the Module’s bottom outlet.Plug the Appliance Module into any wall outlet, adhering to the above stated Electrical Protocol.Wheel (BLACK) to the desired number address (1-16). ![]() Using a small screwdriver set the House Code Wheel (RED) to the setting that matches an X10 PRO Controller (A-P). See then select Technical Support and PLC Troubleshooting. Improving remote communications throughout the home. An alternative solution is recommended, to install a Phase Coupler for If not, the breaker can be changed to the opposite phase. If after installation, an X10 Receiver does not respond to a remote Controller, then check to ensure that the breaker serving the X10 Receiver is on the same phase as the Controller. Each 120V Phase is NOT directly connected with the other 120V phase. Nearly all residential homes are wired SPLIT-PHASE.
0 Comments
Leave a Reply. |